-
1 максимально допустимая температура
3.11 максимально допустимая температура (maximum allowable temperature): Наибольшая допустимая постоянная температура, приемлемая для оборудования (или любой его части) при эксплуатации на указанной рабочей жидкости с указанным рабочим давлением.
Источник: ГОСТ Р 54806-2011: Насосы центробежные. Технические требования. Класс 1 оригинал документа
Русско-английский словарь нормативно-технической терминологии > максимально допустимая температура
-
2 температура окружающей среды
- température ambiante, f
температура окружающей среды
Средняя температура воздуха или другой среды около оборудования.
Примечание - В процессе измерения температуры окружающей среды измерительный прибор (зонд) должен быть экранирован от сквозняков и нагрева излучением.
[ ГОСТ Р МЭК 60050-826-2009]
температура окружающей среды
Температура воздуха или другой среды в непосредственной близости от оборудования или компонента.
[ ГОСТ Р МЭК 60050-426-2006]
температура окружающей среды
Предполагают, что под температурой окружающей среды понимают воздействующие факторы со стороны всего другого оборудования, установленного в том же помещении.
Температура окружающей среды, которую следует учитывать применительно к оборудованию, - это температура в том месте, где оно должно быть установлено, с учетом влияния другого оборудования и источников тепла в том же месте в процессе работы без учета тепла от устанавливаемого оборудования
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]
температура окружающей среды
Температура воздуха или среды в том месте, где должно быть использовано оборудование.
[ ГОСТ Р МЭК 60204-1-2007]EN
ambient temperature
average temperature of air or another medium in the vicinity of the equipment
NOTE – During the measurement of the ambient temperature the measuring instrument/probe should be shielded from draughts and radiant heating.
[IEV number 826-10-03]
ambient temperature
temperature of the air or other medium where the equipment is to be used
[IEC 60204-1-2006]FR
température ambiante, f
température moyenne de l'air ou du milieu au voisinage du matériel
NOTE – Pendant la mesure de la température ambiante il est recommandé que l'instrument/la sonde de mesure soit protégée des courants d'air et de la chaleur rayonnée.
[IEV number 826-10-03]Параллельные тексты EN-RU
The temperate of each module of a Molded Case Circuit Breaker is the sum of temperature increase by conduction and ambient temperature and if the ambient temperature exceeds 40°C the passing current needs to be reduced so that the temperature of such element as internal insulator of MCCB exceed the maximum allowable temperature.
[LS Industrial Systems]Температура частей автоматического выключателя в литом корпусе равна температуре окружающей среды плюс температура, определяемая количеством теплоты, выделяемой при протекании электрического тока. Если автоматический выключатель эксплуатируется при температуре окружающей среды, превышающей 40 °C, то следует учитывать, что номинальный ток такого выключателя будет немного меньше. Учет этого обстоятельства позволит избежать недопустимого нагрева частей автоматического выключателя, выполненных из изоляционного материала.
[Перевод Интент]Тематики
EN
DE
- Umgebungstemperatur, f
FR
- température ambiante, f
Русско-французский словарь нормативно-технической терминологии > температура окружающей среды
-
3 температура окружающей среды
температура окружающей среды
Средняя температура воздуха или другой среды около оборудования.
Примечание - В процессе измерения температуры окружающей среды измерительный прибор (зонд) должен быть экранирован от сквозняков и нагрева излучением.
[ ГОСТ Р МЭК 60050-826-2009]
температура окружающей среды
Температура воздуха или другой среды в непосредственной близости от оборудования или компонента.
[ ГОСТ Р МЭК 60050-426-2006]
температура окружающей среды
Предполагают, что под температурой окружающей среды понимают воздействующие факторы со стороны всего другого оборудования, установленного в том же помещении.
Температура окружающей среды, которую следует учитывать применительно к оборудованию, - это температура в том месте, где оно должно быть установлено, с учетом влияния другого оборудования и источников тепла в том же месте в процессе работы без учета тепла от устанавливаемого оборудования
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]
температура окружающей среды
Температура воздуха или среды в том месте, где должно быть использовано оборудование.
[ ГОСТ Р МЭК 60204-1-2007]EN
ambient temperature
average temperature of air or another medium in the vicinity of the equipment
NOTE – During the measurement of the ambient temperature the measuring instrument/probe should be shielded from draughts and radiant heating.
[IEV number 826-10-03]
ambient temperature
temperature of the air or other medium where the equipment is to be used
[IEC 60204-1-2006]FR
température ambiante, f
température moyenne de l'air ou du milieu au voisinage du matériel
NOTE – Pendant la mesure de la température ambiante il est recommandé que l'instrument/la sonde de mesure soit protégée des courants d'air et de la chaleur rayonnée.
[IEV number 826-10-03]Параллельные тексты EN-RU
The temperate of each module of a Molded Case Circuit Breaker is the sum of temperature increase by conduction and ambient temperature and if the ambient temperature exceeds 40°C the passing current needs to be reduced so that the temperature of such element as internal insulator of MCCB exceed the maximum allowable temperature.
[LS Industrial Systems]Температура частей автоматического выключателя в литом корпусе равна температуре окружающей среды плюс температура, определяемая количеством теплоты, выделяемой при протекании электрического тока. Если автоматический выключатель эксплуатируется при температуре окружающей среды, превышающей 40 °C, то следует учитывать, что номинальный ток такого выключателя будет немного меньше. Учет этого обстоятельства позволит избежать недопустимого нагрева частей автоматического выключателя, выполненных из изоляционного материала.
[Перевод Интент]Тематики
EN
DE
- Umgebungstemperatur, f
FR
- température ambiante, f
3.1 температура окружающей среды (ambient temperature): Температура вокруг рассматриваемого объекта. Если электронагреватели заключены в теплоизоляцию, то температурой окружающей среды считают температуру с внешней стороны такой изоляции.
Источник: ГОСТ Р МЭК 60079-30-1-2009: Взрывоопасные среды. Резистивный распределенный электронагреватель. Часть 30-1. Общие технические требования и методы испытаний оригинал документа
3.1 температура окружающей среды (ambient temperature): Температура воздуха, окружающего испытываемый фильтр.
Источник: ГОСТ Р ИСО 12500-1-2009: Фильтры сжатого воздуха. Методы испытаний. Часть 1. Масла в виде аэрозолей оригинал документа
3.4 температура окружающей среды (ambient temperature): Температура воздуха, окружающего испытываемый фильтр.
Источник: ГОСТ Р ИСО 12500-2-2009: Фильтры сжатого воздуха. Методы испытаний. Часть 2. Пары масел оригинал документа
3.3 температура окружающей среды (ambient temperature): Температура окружающей среды устройства, блока оборудования или установки.
Источник: ГОСТ Р 54110-2010: Водородные генераторы на основе технологий переработки топлива. Часть 1. Безопасность оригинал документа
Русско-английский словарь нормативно-технической терминологии > температура окружающей среды
-
4 температура окружающей среды
- Umgebungstemperatur, f
температура окружающей среды
Средняя температура воздуха или другой среды около оборудования.
Примечание - В процессе измерения температуры окружающей среды измерительный прибор (зонд) должен быть экранирован от сквозняков и нагрева излучением.
[ ГОСТ Р МЭК 60050-826-2009]
температура окружающей среды
Температура воздуха или другой среды в непосредственной близости от оборудования или компонента.
[ ГОСТ Р МЭК 60050-426-2006]
температура окружающей среды
Предполагают, что под температурой окружающей среды понимают воздействующие факторы со стороны всего другого оборудования, установленного в том же помещении.
Температура окружающей среды, которую следует учитывать применительно к оборудованию, - это температура в том месте, где оно должно быть установлено, с учетом влияния другого оборудования и источников тепла в том же месте в процессе работы без учета тепла от устанавливаемого оборудования
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]
температура окружающей среды
Температура воздуха или среды в том месте, где должно быть использовано оборудование.
[ ГОСТ Р МЭК 60204-1-2007]EN
ambient temperature
average temperature of air or another medium in the vicinity of the equipment
NOTE – During the measurement of the ambient temperature the measuring instrument/probe should be shielded from draughts and radiant heating.
[IEV number 826-10-03]
ambient temperature
temperature of the air or other medium where the equipment is to be used
[IEC 60204-1-2006]FR
température ambiante, f
température moyenne de l'air ou du milieu au voisinage du matériel
NOTE – Pendant la mesure de la température ambiante il est recommandé que l'instrument/la sonde de mesure soit protégée des courants d'air et de la chaleur rayonnée.
[IEV number 826-10-03]Параллельные тексты EN-RU
The temperate of each module of a Molded Case Circuit Breaker is the sum of temperature increase by conduction and ambient temperature and if the ambient temperature exceeds 40°C the passing current needs to be reduced so that the temperature of such element as internal insulator of MCCB exceed the maximum allowable temperature.
[LS Industrial Systems]Температура частей автоматического выключателя в литом корпусе равна температуре окружающей среды плюс температура, определяемая количеством теплоты, выделяемой при протекании электрического тока. Если автоматический выключатель эксплуатируется при температуре окружающей среды, превышающей 40 °C, то следует учитывать, что номинальный ток такого выключателя будет немного меньше. Учет этого обстоятельства позволит избежать недопустимого нагрева частей автоматического выключателя, выполненных из изоляционного материала.
[Перевод Интент]Тематики
EN
DE
- Umgebungstemperatur, f
FR
- température ambiante, f
Русско-немецкий словарь нормативно-технической терминологии > температура окружающей среды
-
5 максимально допустимая температура на выходе
максимально допустимая температура на выходе
(напр. углеразмольной мельницы на ТЭС)
[А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]Тематики
EN
Русско-английский словарь нормативно-технической терминологии > максимально допустимая температура на выходе
-
6 вес
weight (wt)
- без топлива (ла) — zero fuel weight
- брутто — gross weight
- в зависимости от высоты (давления) и температуры на аэродроме, максимальный (допустимый) взлетный (параграф разд. 5 рлэ) — takeoff weight-altitude-temperature (wat) curves the wat curves should be provided which limit the weight to an extent necessary to ensure compliance with the airworthiness climb requirements appropriate to takeoff.
- в зависимости от высоты (давления) и температуры на аэродроме, максимальный (допустимый) взлетный (надпись к графику разд. 5 рлэ) — maximum takeoff weight for altitude and temperature the curves should be drawn having the altitude of the airdrome as the ordinate and airplane weight as abscissa, with lines of constant temperature.
- в зависимости от высоты (давления) и температуры на аэродроме, максимальный (допустимый) посадочный (параграф разд. 5 рлэ) — landing weight-altitude-temperature (wat) curves the curves should be drawn to the same specification as for the takeoff wat curves.
- в зависимости от высоты (давления) и температуры на аэродроме, максимально (допустимый) посадочный (график к разд. 5 рлэ) — maximum landing weight for altitude and temperature the graph title should be "maximum landing weight for altitude and temperature".
-, взлетный — takeoff weight
- в тысячах кг (на графике) — weight - thousands of kg
-, выбранный заявителем — weight selected by the applicant
-, гарантированный — guaranteed weight
- десантной нагрузки — air delivery load weight
- загруженного самолета, без топлива, максимальный — maximum zero fuel operational weight
- заправляемого топлива, максимальный (в кг) — maximum fuel load weight
- из условия располагаемой энергоемкости тормозов (колес), максимально допустимый взлетный — maximum allowable takeoff weight restricted /permitted/ by brake kinetic energy absorption (capacity)
-, завышенный (напр. при посадке) — overweight
-, максимальный взлетный — maximum takeoff weight
-, максимально допустимый взлетный — maximum allowable takeoff weight
-, максимальный посадочный — maximum landing weight
-, максимальный расчетный полетный — maximum design flight weight (mfw)
максимальный расчетный вес, ограниченный условиями прочности ла и другими требованиями летной годности. — the maximum weight for flight as limited by aircraft strength and other airworthiness requirements.
-, максимальный (расчетный) рулежный — maximum (design) taxi weight
максимальный предвзлетный вес ла, включающий вес топлива на выруливание и опробование двигателей. — the maximum weight allowed for ground maneuver includes weight of taxi and run-up fuel.
-, максимальный сертифицированный (установленный в соответствии с нормами летной годности) — maximum certificate(d) weight maximum certificate weights are determined in accordance with the airworthiness requirements.
-, маршрутный (полетный) — en-route weight
-, минимальный — minimum weight
-, наибольший — highest weight
-, наименьший — lowest weight
- начала перекачки топлива, максимальный расчетный — maximum design fuel transfer weight (mftw)
-, ограниченный заявителем, наибольший — highest weight selected by the applicant
-, ограниченный по набору высоты, максимально допустимый взлетный — maximum allowable takeoff weight restricted /permitted/ by climb performance
-, ограниченный по набору высоты при уходе на второй круг, максимально допустимый посадочный — maximum allowable landing weight restricted by climb performance during go-around (сша)
maximum landing weight permitted by balked landing climb performance (англ.)
-, ограниченный располагаемой длиной впп, максимально допустимый посадочный — maximum allowable landing weight permitted by landing field length available
-, ограниченный располагаемой энергоемкостью колес (тормозов), максимально допустимый взлетный — maximum allowable takeoff weight restricted /permitted/ by brake kinetic energy absorption capacity
-, ограниченный скоростью вращения колес максимально допустимый взлетный — maximum allowable takeoff weight restricted by tire speed
- перегрузочный — overload weight, overweight
- по формуляру — logged weight, weight specified in log book
- полезной нагрузки — useful load weight
-, полетный (в рлэ, на графиках) — gross weight (gw)
-, полетный (по британским нормам летной годности bcar) — en-route weight
- полной нагрузки (вес экипажа, топлива и полезной нагрузки) — full load weight
-, посадочный (нормальный) — landing weight
- предельный — maximum weight
- предельный, взлетный — maximum takeoff weight
- предельный /полный/ полетный — gross weight
- при начальном наборе высоты — climbout weight
-, приведенный взлетный — factored takeoff weight
- пустого самолета — empty weight
- пустого самолета, базовый — basic empty weight (bew)
- пустого самолета в состоянии поставки — delivery empty weight (dew) manufacturer's empty weight less any shortages, plus those standard items and operational items in aircraft at time of delivery.
- пустого самолета, основной — basic empty weight (bew) standard basic empty weight plus or minus weight of standard item variations.
- пустого самолета, производственный — manufacturer's empty weight (mew)
вес конструкции, силовой установки, систем и оборудования, которые являются составной частью конкретного ла. — the weight of the structure, powerplant, furnishings, systems and other items of equipment that are considered an integral part of a particular aircraft configuration.
- пустого самолета с полным снаряжением — operational empty weight
- пустого снаряженного самолета — operational empty weight (oew)
basic empty weight or fleet empty weight plus operational items.
-, расчетный — design weight
-, расчетный взлетный — design takeoff weight
-, расчетный полетный — (maximum) design flight weight
-, расчетный посадочный — design landing weight
-, рулежный — taxi weight,
- самолета (обозначение оси графика изменения веса в полете) — gross /en-route/ weight
- самолета без топлива — zero fuel weight
-, сертифицированный — certificate(d) weight
-, скорректированный — corrected weight
- служебной нагрузки — weight of standard items
- снаряжения самолета (с экипажем и бортпроводниками) — weight of (aircraft) operational items
- снаряженного самолета — operational weight
- снаряженного самолета, взлетный — operational takeoff weight (otow)
- снаряженного самолета, посадочный — operational landing weight (olw)
- (самолета) с полным снаряжением (со снаряжением) — operational weight
-, стандартный — standard weight
-, сухой — dry weight
вес двигателя с установленными агрегатами, без охлаждающей жидкости, масла и топлива — the weight of an engine exclusive of fuel, oil, and liquid coolant.
- тары — tare weight
-, транспортировочный — shipping weight
-, удельный — specific gravity
- удельный, топлива — fuel specific gravity
- установленный (для конкретных условий, ограничений) — authorized weight (for takeoff or landing)
-, чистый — net weight
-, эксплуатационный (ла) — operational weight
выигрыш в в. — saving of weight
избыток в. — excess weight
по в. — by weight
%-ный раствор по в. — % by weight solution
под своим в. — due to own weight
клапан свободно входит в гильзу под действием своего веса. — the valve drops freely into the sleeve due to its own weight.
при любом в. — at any weight
разбивка в. (ла на составляющие: вес конструкции, топлива, снаряжения и т.д.) — weight breakdown
выигрывать в в. — save weight
проигрывать в в. — have weight penalty
уменьшать в. — reduce weight
химическое фрезерование и сотовые конструкции применяются для уменьшения веса самолета. — chemical milling and honeycomb construction are techniques developed to reduce the aircraft weight.
увеличивать в. — increase weightРусско-английский сборник авиационно-технических терминов > вес
-
7 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
-
8 длительный допустимый ток
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-английский словарь нормативно-технической терминологии > длительный допустимый ток
-
9 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
10 предельный
1. extreme2. overallобщий спрос; предельный спрос — overall demand
3. supreme4. to the limitпредельный срок службы; ресурс — age limit
предельный вираж — power limited 360° turn
5. maximumмаксимальная ошибка; предельная ошибка — maximum error
6. maximumlly7. mostly8. marginal9. utmost10. go-no-go11. limiting12. saturated13. terminal14. tolerance15. ultimate16. limit; maximum; utmost; extremeлимитная цена; предельная цена — price limit
17. uttermostСинонимический ряд:наибольший (прил.) максимальный; наибольший; самый большой -
11 турбина
turbine
лопаточная машина, в которой энергия потока газа, протекающего через направляющий (сопловой) аппарат и рабочие лопатки ротора, преобразуется в механическую paботу на валу машины (рис.46). — а multibladed wheel or rotor of а gas-turbine engine, rotated by the impulse from or reaction to the gas passing across the blades. consists principally of one or more turbine wheels and a stator.
-, активная (газовая) — impulse turbine
-,бортовая вспомогательная (всу) — auxiliary pover unit(apu)
-, вторая (низкого давления в двухроторном гтд) — low pressure turbine, lp turbine
- (каскада) высокого давления — high-pressure turbine, hp turbine
турбина высокого давления спужит для привода компрессора высокого давления. — the high-pressure (hp) turbine drives the high-pressure (hp) compressor (rotor).
- газогенератора — gas-generator /-producer/ turbine
-, двухступенчатая — two-stage turbine
- компрессора (двигателя со свободной турбиной) — compressor turbine
-, многоступенчатая — multistage turbine
турбина с несколькими последовательно расположеннымн ступенями. — а turbine consisting of several stages.
- (привода) несущего винта (свободная или силовая турбина) — free (power) turbine
- (каскада) низкого давления — low-pressure turbine, lp turbine
для привода компрессора нд. — lp turbine drives lp cornpressor.
-, одноступенчатая — single-stage turbine
турбина с одним рабочим колесом и одним сопловым аппаратом. — а turbine having one set of stater blades followed by а set of rotor blades.
-, осевая — axial-flow turbine
турбина, в которой поток газа движется в направлении параллельном оси турбины. — а turbine through which the general direction of flow is axial.
-, первая (высокого давления в двухроторном гтд) — high pressure turbine, hp turbine
- привода постоянных оборотов (ппо) — constant speed drive turbine
-, промежуточная (промежуточного каскада между турбинами вд и нд) — intermediate pressure turbine
-, противоточная — reverse-fiow turbine
-, работающая на выхлопных газах (для пд) — power recovery turbine
турбина, вращающаяся выхлопными газами и кинематически связанная с коленвалом. — for reciprocating engines only. the ttirbina which ехtracts energy from the ехhatist gases arid as coupled to the crankshaft
-, реактивная — reaction turbine
турбина, в которой расширение газа происходит не только в сопловом аппарате, но и в рабочем колесе. — а type of turbine having rotor blades shaped so that they form а ring of nozzles, the turbine being rotated by the rgaetiorl of the fluid ejected from between the blades.
-, свободная (рис.46) — free turbine
-, свободная силовая — free powar turbine
-, силовая (свободная), с npотивоположным вращением рабочих колес — contra-rotating power turbine
- с приводом от набегающегo потока — ram air iurbine (rat) extend rat to pressursze hydraulic aystem.
"- (с приводом от набегающего потока) включена (работает)" (табло) — rat deployed
- стартера — starter turbine
- трехкаскадная (с приводом от трех валов) — triple-shaft turbine this turbine consists of а hp turbine, intermediate pressure turbine and lp turbine.
-, утилизирующая (выхлопные газы пд) — power recovery turbine
·-, центробежная — radial-flow turbine
турбина, в которой газ движется в направлении перпендикулярном к оси турбины, — а turbine through which the general direction of flow being radial.
-, четырехступенчатая давление (газов) за т. (p4) давление перед т. (рз) за т. — four-stage turbine turbine exhaust pressure (p,4) turbine inlet pressure (рз) past turbine, at turbine outlet
maximum allowable gas temperature past turbine.
перед т. температура выходящих газов за т. — before turbine, at turbine inlet turbine gas temperature (tgt)Русско-английский сборник авиационно-технических терминов > турбина
-
12 максимальная допустимая рабочая температура
Engineering: maximum allowable working temperatureУниверсальный русско-английский словарь > максимальная допустимая рабочая температура
-
13 максимально допустимая рабочая температура
Engineering: maximum allowable working temperatureУниверсальный русско-английский словарь > максимально допустимая рабочая температура
-
14 намного превышающий
Намного превышающийThese results show that the combustor is operating with CO and UHC levels much in excess of the program goals.These enhancements in cooling have enabled turbines to operate with gas temperatures well in excess of the maximum allowable metal temperature.Русско-английский научно-технический словарь переводчика > намного превышающий
-
15 ограничиваться
Ограничиваться - to be limited to, to be restricted to, to be confined to, to be bounded to; to confine itself toIn the coal-fired central power station the maximum steam temperature is restricted to a level near 565 to 595°C.In that model yield is confined to an infinitesimal strip coplanar with the crack.This nonmandatory appendix confines itself to establishing allowable loads, but leaves the determination of actual loads to the designer.Русско-английский научно-технический словарь переводчика > ограничиваться
-
16 масса
масса сущ1. mass2. weight бортовая система определения массы и центровкиonboard weight and balance systemвзлетная масса1. takeoff weight2. takeoff mass воздушная массаair massвоздушное судно небольшой массыlight aircraftвосходящий порыв воздушной массыair-up gustдопуск на массу воздушного суднаaircraft weight toleranceдопустимая посадочная масса1. allowable landing weight2. aircraft operational empty weight завихрение воздушной массыwhirlwindизбыточная масса1. overweight2. excess weight исходная масса пустого воздушного суднаbasic empty weightкоммерческая загрузка, ограниченная по массеweight limited payloadмаксимальная сертифицированная взлетная массаmaximum certificate takeoff massмаксимально допустимая взлетная массаmaximum takeoff weightмаксимально допустимая масса1. authorized weight2. maximum permitted weight максимально допустимая масса при стоянкеmaximum ramp massмаксимально допустимая масса при стоянке на перронеmaximum apron massмаксимально допустимая посадочная массаmaximum permitted landing weightмасса без топлива1. zero fuel mass2. zero fuel weight масса конструкции1. deadload2. dead load масса при начальном наборе высотыclimbout weightмасса пустого воздушного судна1. base weight2. aircraft empty weight 3. empty weight масса пустого воздушного судна при поставкеdelivery empty weightмасса снаряженного воздушного судна без пассажировaircraft operational weightнисходящий порыв воздушной массыair-down gustобщая взлетная массаtakeoff gross weightобщая масса1. combined mass2. gross mass 3. aggregate weight 4. gross weight ограничение по массеweight limitationориентировочная массаtentative weightплотность массыmass densityполетная масса1. airborne weight2. flying weight полная взлетная массаallowable takeoff weightполная массаwet weightполная полетная масса1. all-up weight2. all-up mass поправка на взлетную массуtakeoff mass correctionпоправка на массуmass correctionпоправка на массу при заходе на посадкуapproach mass correctionпорыв воздушной массыair gustпосадка с превышением допустимой посадочной массыoverweight landingпосадочная масса1. landing weight2. landing mass 3. touchdown weight предел ограничения массыlimiting range of massрадиозондовое наблюдение за состоянием воздушных массrawinsonde observationразбивка массыmass breakdownраспределение массы1. mass distribution2. weight distribution расход массыmass flowрасчетная взлетная масса1. design takeoff mass2. design takeoff weight расчетная масса1. estimated weight2. calculated mass расчетная масса при руленииdesign taxiing massрасчетная полетная массаdesign flight weightрасчетная посадочная масса1. design landing mass2. design landing weight рулежная массаtaxi weightсертифицированная взлетная массаcertificated takeoff weightсистема сборов по фактической массеweight system(багажа или груза) скорость движения воздушной массыair velocityтемпература возмущенной воздушной массыstatic air temperatureтранспортировочная массаshipping weightугол входа воздушной массыangle of indraftустойчивость воздушной массыair stabilityцентр массcenter of massшасси, выпускающееся под действием собственной массыfree-fall landing gearэксплуатационная массаoperating massэнергия порыва воздушной массыgust load -
17 максимальный
•The light intensity was a maximum in the centre of the laser beam.
•Dip is at its maximum over the magnetic poles.
•The peak blade speed...
•The production of this compound is attended with the maximum heat evolution.
•In order to get the most heat economy,...
•Table 10 gives the top Curie temperature of various material systems.
* * *Максимальный -- maximum, peak, top, ultimate, the most; at its greatestWhere fatigue is a consideration, peak stresses will have to be compared with allowable values.Top size 3/8" (максимальный размер частиц 3/8 дюйма)Chuck capacity (максимальный диаметр сверла, зажимаемого в патроне)It is the degree of prior work-hardening in the primary zone that has the most influence.Русско-английский научно-технический словарь переводчика > максимальный
См. также в других словарях:
maximum — maximumly, adv. /mak seuh meuhm/, n., pl. maximums, maxima / meuh/, adj. n. 1. the greatest quantity or amount possible, assignable, allowable, etc. 2. the highest amount, value, or degree attained or recorded. 3. an upper limit allowed or… … Universalium
Reflow soldering — is a process in which a solder paste (a sticky mixture of powdered solder and flux) is used to temporarily hold the components to their attachment pads, after which the assembly is carefully heated in order to solder the joint. The assembly may… … Wikipedia
ГОСТ 24856-81: Арматура трубопроводная промышленная. Термины и определения — Терминология ГОСТ 24856 81: Арматура трубопроводная промышленная. Термины и определения оригинал документа: 18. Арматура под приварку Определения термина из разных документов: Арматура под приварку 29. Двухседельный регулирующий клапан … Словарь-справочник терминов нормативно-технической документации
максимально допустимая температура — 3.11 максимально допустимая температура (maximum allowable temperature): Наибольшая допустимая постоянная температура, приемлемая для оборудования (или любой его части) при эксплуатации на указанной рабочей жидкости с указанным рабочим давлением … Словарь-справочник терминов нормативно-технической документации
ГОСТ Р 54806-2011: Насосы центробежные. Технические требования. Класс 1 — Терминология ГОСТ Р 54806 2011: Насосы центробежные. Технические требования. Класс 1 оригинал документа: 3.6 базовое расчетное давление (basic design pressure): Давление, подвергающее примененный материал находящихся под давлением деталей… … Словарь-справочник терминов нормативно-технической документации
Thermal resistance in electronics — Thermal resistance is the temperature difference across a structure when a unit of heat energy flows through it in unit time. It is the reciprocal of thermal conductance. The SI units of thermal resistance are kelvins per watt, or the equivalent… … Wikipedia
температура окружающей среды — Средняя температура воздуха или другой среды около оборудования. Примечание В процессе измерения температуры окружающей среды измерительный прибор (зонд) должен быть экранирован от сквозняков и нагрева излучением. [ГОСТ Р МЭК 60050 826 2009]… … Справочник технического переводчика
Oxide dispersion strengthened alloy — Oxide dispersion strengthened alloys (ODS) are used for high temperature turbine blades and heat exchanger tubing.[1] Alloys of nickel are the most common but work is being done on iron aluminum alloys.[2] ODS steels are used in nuclear… … Wikipedia
Oxide dispersion strengthened — ODS materials are used on spacecrafts as a layer designed to protect the vehicle, especially during reentry into the atmosphere.When it comes to reentry at hypersonic speeds, the properties of gasses change dramatically. Shockwaves are created… … Wikipedia
Nuclear power plant — This article is about electricity generation from nuclear power. For the general topic of nuclear power, see Nuclear power. A nuclear power station. The nuclear reactor is contained inside the cylindrical containment buildings to the right left… … Wikipedia
environmental works — ▪ civil engineering Introduction infrastructure that provides cities and towns with water supply, waste disposal, and pollution control services. They include extensive networks of reservoirs, pipelines, treatment systems, pumping stations … Universalium